Exadata X7-2 Hardware
 
Zero Data Loss Recovery Appliance X7 Hardware
 
Oracle SuperCluster M8 Hardware
 
Exadata X7-8 Hardware
 

PLA-Support>Sun Systems>Sun_Other>Sun Collections>SN-OTH: x64-CAP VCAP
 

In this Document

Goal

Solution

References

Oracle Confidential PARTNER - Available to partners (SUN).
Reason: Exadata internal only for Oracle support engineers use and approved HW partners

Applies to:

Goal

How to Replace an Exadata X7-2 Storage Cell Server Coin Cell Battery.

Solution

DISPATCH INSTRUCTIONS:

WHAT SKILLS DOES THE FIELD ENGINEER/ADMINISTRATOR NEED?: Exadata X7-2 Training

TIME ESTIMATE: 30 minutes

TASK COMPLEXITY: 2

FIELD ENGINEER/ADMINISTRATOR INSTRUCTIONS:

PROBLEM OVERVIEW:  An Exadata X7-2 Storage Cell Server Coin Cell Battery needs replacement

WHAT STATE SHOULD THE SYSTEM BE IN TO BE READY TO PERFORM THE RESOLUTION ACTIVITY?:

IMPORTANT NOTE TO TSC ENGINEER:  CUT & PASTE the “CUSTOMER ACTIVITY” sections of the Pre-Replacement and Post-Replacement steps into a SR Note and ensure the customer is aware to do these steps prior to the scheduled field engineer activity, and during and after the replacement activity.

CUSTOMER ACTIVITY:

Shutdown of the storage cell is required prior to the part replacement:

Complete Steps 1 to 6 of Note ID 1188080.1 “Steps to shut down or reboot an Exadata storage cell without affecting ASM”.

Where noted, the SQL, CellCLI and commands under ‘root’ should be run by the Customers DBA, unless the Customer provides login access to the Field Engineer

These steps are also provided in the documentation:
   https://docs.oracle.com/cd/E80920_01/DBMMN/maintaining-exadata-storage-servers.htm#DBMMN21128

WHAT ACTION DOES THE FIELD ENGINEER/ADMINISTRATOR NEED TO TAKE?:

Prepare the Server for Service

The customer should have already prepared the server and powered it off.  If not, provide them the instructions in the previous section.

1. Extend the server to the maintenance position
2. Disconnect the power cords from the power supplies.
3. Attach an anti-static wrist strap to your wrist and to a metal area on the chassis or the rack.
4. Remove the server top cover. Use a Torx T10 screwdriver to unlock the release button latch.

Removing the Coin Cell Battery

1. To dislodge the battery from its retainer, gently push the top edge of the battery away from the retainer.

2. Lift the battery up and out of its retainer.

Installing the Coin Cell Battery

1. Unpack the replacement battery.
2. Press the new battery into the battery retainer so that the + positive side faces the plastic of the retainer and the - negative side is making contact with the metal clip.

Return the Server to Operation

1. Install the server top cover. Use a Torx T10 screwdriver to lock the release button latch.
2. Reconnect the power cords to the server power supply and connect any other cables to their original locations.
3. Return the server to the normal rack position.
4. Once the power cords have been re-attached and the ILOM has booted you will see a slow blink on the green LED for the server. Power on the
server by pressing the power button on the front of the unit.
5. Connect to the server console via the ILOM and monitor the boot.
      By default the ILOM serial console displays the primary console output.
      In the event of unexpected boot behavior, it is advisable to connect to both ILOM serial and ILOM graphics consoles at the same time and monitor.

OBTAIN CUSTOMER ACCEPTANCE

WHAT ACTION DOES THE FIELD ENGINEER/ADMINISTRATOR NEED TO TAKE TO RETURN THE SYSTEM TO AN OPERATIONAL STATE?:

FIELD SERVICE ENGINEER and CUSTOMER ACTIVITY:

1. Verify all expected hardware is visible to the server and the fault is cleared. Assistance from the customer for server login access will be required.

2. The service processor is configured to synchronize with a network time server using the Network Time Protocol (NTP), the Oracle ILOM clock will be reset as soon as the server is powered on and connected to the network. Login to the server as 'root' user and verify the correct time and date and timezone in the OS and in ILOM:

3. Verify there are no outstanding faults in ILOM:

4. Verify there are no outstanding alerts in the Cell:

5. Re-activate the Storage Cell grid disks.  Follow Steps 7 to 10 of Note ID 1188080.1 “Steps to shut down or reboot an Exadata storage cell without affecting ASM”.

Where noted, the SQL, CellCLI and commands under ‘root’ should be run by the Customers DBA, unless the Customer provides login access to the Field Engineer.

These steps are also provided in the documentation:
 https://docs.oracle.com/cd/E80920_01/DBMMN/maintaining-exadata-storage-servers.htm#DBMMN21128

PARTS NOTE:

370-5621 3V Coin Cell Battery

REFERENCE INFORMATION:

Oracle Exadata Database Machine Maintenance Guide: https://docs.oracle.com/cd/E80920_01/DBMMN/maintaining-exadata-storage-servers.htm#DBMMN21128

Oracle Server X7-2L Documentation https://docs.oracle.com/cd/E72463_01/index.html

Steps to shut down or reboot an Exadata storage cell without affecting ASM (Doc ID 1188080.1)

This solution has no attachment