Netra Modular System
 

PLA-Support>Sun Systems>x86>Server>SN-x64: TELCO-NETRA
 

In this Document

Goal

Solution

Oracle Confidential PARTNER - Available to partners (SUN).
Reason: < Internal_Only > Oracle Confidential (Distribution). Do not distribute to customers < /Internal_Only >

Applies to:

Goal

How to Power Cycle reset the FMM (Frame Management Module) in an NMS (Netra Modular System)

Solution

Step overview:

Step details.

1. Connect to the FMM as root. 
   
 One method would be to connect into the FMM serial mgmt. port via the RJ45 coupler panel port 40.

Another method is to ssh in from one of the compute nodes. 

2a. Get the three items needed to generate an escalation mode password

2b. Open a collab to get an escalation mode password. 
     Someone will create the escalation mode password for you using the three items collected:

 3. Create a new user with correct access roles. 
     The example shown creates the user 'modechange' with password 'changeme' and sets the roles to 'aoucrs'
     After the new user has been created, logout from the current session.

4. Login as the newly created user

5. Enter escalation mode where you can issue the i2ctool command.
    When in escalation mode, the prompt changes and you will be at the bash shell where you can enter unix commands.
    Enter this command:  i2ctool -B 3 -d 0x42 -w 2 0xff

6. After the FMM has been power cycled, login again as root and check the clock. 
   The current FMM has no onboard battery and the date may get reset to Dec 31, 1969.
   If needed, set the FMM clock using the format this format: MMDDhhmmYYYY

7. Remove the newly created user from step 3.

Enter the following command to reset the FMM

[(flash)root@ORACLEFMM-489089M+1515CK0032:~]# i2ctool -B 3 -d 0x42 -w 2 0xff

U-Boot 2010.03

Custom Pilot3 U-Boot 0.1 (Jul  6 2015 - 15:17:32) r101001

VGA buffer reserved 0x800000 bytes at 0x80000000
sptrace allocated 0x400000 bytes at 0x9FC00000
DRAM:  500 MB
Flash: 64 MB
Environtment Variable CRC: Calculated: 8cbcd549, Expected: 8cbcd549
In:    serial
Out:   serial
Err:   serial
....done

  ARM restart caused by: power-on
  hardware interface reset by: none
  Galactic1: 0x900, Galactic2: 0x0

pilot3 chip revision : 0x5
SP Debug Jumper:  Empty
SP CLR_PASSD Jumper:  Empty
SP Board revision: 0x1
System Memory Configuration:
    Type: DDR3
    ECC: disabled
    Size: 512 MB
    VGA Memory: 8 MB
    sptrace Memory: 4 MB
    Write CAS: 5
    Read CAS: 9
Date: 2000-01-01 (Sunday)    Time:  0:00:17
Reading FRUID...
Platform Type: ncgf-fmm
Ethaddr is 0:21:28:4f:34:c
Eth1addr is 0:21:28:4f:34:d
Net:   Found Broadcom phy 0 PhyId 5d12
Found Broadcom phy 1 PhyId 5d12
pilot_eth0, pilot_eth1
Enter Diagnostics Mode ['q'uick/'n'ormal(default)/e'x'tended(manufacturing mode)] .....   0
Diagnostics Mode - NORMAL
<DIAGS> ncgf-fmm Service Processor POST - Start
<DIAGS> U-Boot 2010.03
<DIAGS> Custom Pilot3 U-Boot 0.1 (Jul  6 2015 - 15:18:42) r101001
<DIAGS> Date: 2000-01-01 (Sunday)    Time:  0:00:28

<DIAGS> Memory Data Bus Test ... PASSED
<DIAGS> Memory Address Bus Test ... PASSED
<DIAGS> Testing Watchdog ... wd is active, expires in 32 seconds
PASSED
I2C Probe Test - SP
        Bus     Device                          Address Result
        ===     ============================    ======= ======
         1                  SP FRUID (U1301)    0xA0    PASSED
         1               DS1338(RTC) (U1302)    0xD0    PASSED
         3                FMM FRU ID (U6101)    0xA0    PASSED
         3                FMM Config (U6102)    0xA2    PASSED
         3              Frame Config (U6103)    0xA6    PASSED

<DIAGS> PHY #0 R/W Test ... PASSED
<DIAGS> PHY #0 Link Status ... PASSED
<DIAGS> PHY #1 R/W Test ... PASSED
<DIAGS> PHY #1 Link Status ... PASSED
<DIAGS> Testing RTC ... PASSED
checking for abnormal reboots: 1.
Booting linux in 5 seconds...
    Date ='Mon Jul  6 16:12:05 EDT 2015', Build ='r101001'
    uboot @0c0000 OK, kernel @142000 OK, root @340000 OK
    Date ='Wed Mar 11 15:27:57 PDT 2015', Build ='r97615'
    uboot @20c0000 OK, kernel @2142000 OK, root @2340000 OK
Primary image is type ILOM, address 00140000
Secondary image is type ILOM, address 02140000
....done
Un-Protect Flash Bank # 1
Un-Protect Flash Bank # 2
Trying primary image...
Trying to boot package at 00140000
Found kernel image at 00142000
Found root image at 00340000
bootargs= root=/dev/mtdblock2 rootfstype=squashfs ro  console=ttyS0,9600 bigphysarea=2816 ractrends.mtdblocks=sppost_log,0x80000,0x40000,root,0x340000,0xac0000,env,0x40000,0x40000,params,0x4000000,0x400000,persist,0x4400000,0x400000,coredump,0x4800000,0x800000,
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   Linux-2.6.27.43
   Created:      2015-07-06  19:11:45 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1769552 Bytes =  1.7 MB
   Load Address: 80808000
   Entry Point:  80808000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Boot Enet is 0:21:28:4f:34:c
Galactic register 1: 10900
Starting watchdog timer.

Starting kernel ...

Uncompressing Linux.................................................................................................................. done, booting the kernel.
Linux version 2.6.27.43 (ilom@oracle) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 Mon Jul 6 15:11:30 EDT 2015
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: ServerEngines PILOT3
Memory policy: ECC disabled, Data cache writethrough
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 127000
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs ro  console=ttyS0,9600 bigphysarea=2816 ractrends.mtdblocks=sppost_log,0x80000,0x40000,root,0x340000,0xac0000,env,0x40000,0x40000,params,0x4000000,0x400000,persist,0x4400000,0x400000,coredump,0x4800000,0x800000,
Pilot-II Interrupt Controller Enabled
PID hash table entries: 2048 (order: 11, 8192 bytes)
Pilot-II Timer Initialized
Pilot-II Timer Started
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 500MB = 500MB total
Memory: 492416KB available (3272K code, 221K data, 128K init)
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: Testing write buffer coherency: ok
net_namespace: 756 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
bigphysarea: Allocated 2816 pages at 0xc0784000.
squashfs: version 3.4 (2008/08/26) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 962
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Pilot 3 SP/SIO serial output muxing support driver v0.1 Built: Jul  6 2015 at 15:11:11.
Unable to determine current serial console mode.  UPCTL=0x2401.  Setting serial console MUX to SP.
Pilot 3 SP/SIO serial output muxing support chrdev registered.
Serial: 8250/16550 driver5 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x40431000 (irq = 20) is a 16550A
serial8250.0: ttyS1 at MMIO 0x40415000 (irq = 40) is a 16550A
serial8250.0: ttyS2 at MMIO 0x40430000 (irq = 53) is a 16550A
serial8250.0: ttyS3 at MMIO 0x40432000 (irq = 21) is a 16550A
serial8250.0: ttyS4 at MMIO 0x40416000 (irq = 41) is a 16550A
brd: module loaded
loop: module loaded
PPP generic driver version 2.4.2
rtl8150: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new interface driver rtl8150
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
Linux PilotII Tulip driver version 1.1.13 (May 11, 2002)
name is Pilot2 Tulip
Reading PHY Mnfc Id for MAC0
Broadcom: PHY found at phy address 16
eth0: Pilot2 Tulip rev 0 at f0500000, 00:21:28:4F:34:0C, IRQ 0.
name is Pilot2 Tulip
Reading PHY Mnfc Id for MAC1
Broadcom: PHY found at phy address 1
eth1: Pilot2 Tulip rev 0 at f0600000, 00:21:28:4F:34:0D, IRQ 1.
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
Ractrends Flash mapping: 0x2000000 at 0x0
SPI: probing for m25pxx devices ...
Found SPI Chip Macronix MX25L25635E
0 65536 512 512
Ractrends Flash mapping: 0x2000000 at 0x2000000
SPI: probing for m25pxx devices ...
Found SPI Chip Micron N25Q256A13EXX40X
0 65536 512 512
Number of banks found = 2
Concatenating MTD devices:
(0): "Bank #0"
(1): "Bank #1"
into device "Concatenated Flash Banks"
GetMTDPartitions() says string is "sppost_log,0x80000,0x40000,root,0x340000,0xac0000,env,0x40000,0x40000,params,0x4000000,0x400000,persist,0x4400000,0x400000,coredump,0x4800000,0x800000,"
MTD Partition 0 : fullpart @ 0x0 of Size 0x4000000
MTD Partition 1 : sppost_log @ 0x80000 of Size 0x40000
MTD Partition 2 : root @ 0x340000 of Size 0xac0000
MTD Partition 3 : env @ 0x40000 of Size 0x40000
MTD Partition 4 : params @ 0x4000000 of Size 0x400000
MTD Partition 5 : persist @ 0x4400000 of Size 0x400000
MTD Partition 6 : coredump @ 0x4800000 of Size 0x800000
FlashSize=0x2000000, PartitionCount=4
Creating 4 MTD partitions on "Concatenated Flash Banks":
0x00000000-0x04000000 : "fullpart"
0x00080000-0x000c0000 : "sppost_log"
0x00340000-0x00e00000 : "root"
0x00040000-0x00080000 : "env"
usbmon: debugfs is not available
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
wdt: EMX WDT is installed.
wdt: EMX WDT nowayout = 1, heartbeat = 30 secs
wdt: EMX WDT guardstartupshutdown = 1
wdt: EMX WDT startuptimeout = 600, shutdowntimeout = 60
wdt: EMX WDT was enabled at driver start, time remaining 592 secs.
wdt: Guarding startup, setting watchdog for 600 seconds.
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
oprofile: using timer interrupt.
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 128K
INIT: version 2.88 booting
Creating /var tmpfs
Creating directories in /var...done.
Creating /var/log tmpfs...done.
Running ldconfig...done
Cleaning up ifupdown....
Calculating moduloading pilot3-nand 1.1le dependencies.NAND device id : 0x2600382c
.. done.
LoadinSetting ONFI access
g kernel module ID Byte 0 is 2c
flashinfo.
LoadID Byte 1 is 38
ing kernel modulID Byte 2 is 0
e nandflash.
ID Byte 3 is 26
ID Byte 4 is 85
Detected a MICRON ONFI 8Gb or 16Gb device
page size 4096 OOB/512 28 pages/block 128 blocks/LUN 2048 LUN single
page size 4096 OOB/page 224 OOB/512 28
Scanning device for bad blocks
adding nand partition, name : params, offset 0x0 size 0x400000
adding nand partition, name : persist, offset 0x400000 size 0x400000
adding nand partition, name : coredump, offset 0x800000 size 0x800000
Creating 7 MTD partitions on "MICRON ONFI":
0x00000000-0x00400000 : "params"
0x00400000-0x00800000 : "persist"
0x00800000-0x01000000 : "coredump"
0x01000000-0x11000000 : "large"
0x11000000-0x21000000 : "spare_partition"
0x21000000-0x31000000 : "huge1"
0x31000000-0x40000000 : "huge2"
Loading kernel module helper.
Helper Module Driver Version 1.1
Copyright (c) 2006 American Megatrends Inc.
i2c_boardinfo: module license 'unspecified' taints kernel.
Loading kernel module gpiomgr.
Loading kernel module gpioint.
Loading kernel module i2c-core.
i2c /dev entries driver
Loading kernel module i2c-dev.
Loading kernel mI2C0: Hardware routines registered
odule i2c-pilot-Registered bus id: i2c-0
ii.
I2C1: Hardware routines registered
Registered bus id: i2c-1
I2C2: Hardware routines registered
Registered bus id: i2c-2
I2C3: Hardware routines registered
Registered bus id: i2c-3
I2C4: Hardware routines registered
Registered bus id: i2c-4
I2C5: Hardware routines registered
Registered bus id: i2c-5
I2C6: Hardware routines registered
Registered bus id: i2c-6
I2C7: Hardware routines registered
Registered bus id: i2c-7
sptrace initialized, base=0x9fc00000, len=0x400000.
Loading kernel module i2c-boardinfo.
Loading kernel module sptrace.
00:00:11 Checking device file systems
00:00:12 Checking persist...
00:00:14 Checking params...
jffs2_scan_inode_node(): CRC failed on node at 0x00085fd0: Read 0xffffffff, calculated 0x92867658
Empty flash at 0x00107304 ends at 0x00108000
00:00:19 Checking coredump...
Empty flash at 0x002b3afc ends at 0x002b4000
00:00:22 Finished check of device file systems

Checking configuration files state ...
Image date:  Mon Jul  6 16:12:05 EDT 2015       Image revision: 101001
Conf date:   Mon Jul  6 16:12:05 EDT 2015       Conf revision:  101001
Configuration files state good after upgrade.
Setting the system clock.
Unable to set System Clock to: Thu Jan 1 00:00:23 UTC 1970 ... (warning).
JFFS2 notice: (549) check_node_data: wrong data CRC in data node at 0x002bd6cc: read 0x325a05a0, calculated 0x1459d64a.
Initializing SP Trace Buffers
Setting up networking....
Will now mount local filesystems:.
Will now activate swapfile swap:done.
Cleaning up temporary files...Cleaning /var/run...done.
Cleaning /var/lock...done.
.
Initializing Inv Cache done
Setting kernel variables ... /etc/sysctl.conf...done.
Starting NMS Intialization

Frame number: 0
Number of frames in the configuration: 1
Frame Config ID is 3
Frame Config is based on SEEPROM spec rev 16
-------------------------------------------
FBN num         Is it in config
-------------------------------------------
1               Is not in config
2               Is in config and is present
3               Is in config and is present
4               Is in config and is present
5               Is in config and is present
6               Is in config and is present
7               Is in config and is present
8               Is in config and is present
9               Is in config and is present
10              Is in config and is present
11              Is in config and is present
12              Is in config and is present
13              Is in config and is present
14              Is in config and is present
15              Is in config and is present
16              Is in config and is present
17              Is in config and is present
18              Is in config and is present
19              Is in config and is present
20              Is in config and is present
21              Is in config and is present
22              Is in config and is present
23              Is in config and is present
24              Is not in config
25              Is in config and is present
26              Is in config and is present
27              Is in config and is present
28              Is in config and is present
29              Is in config and is present
30              Is in config and is present
31              Is in config and is present
32              Is in config and is present
--------------------------------------------
Starting capidirect daemon: capidirectd . Done
Setting hostname to 'ORACLEFMM-489089M+1515CK0032'...Hostname: ORACLEFMM-489089M+1515CK0032.

done.
Configuring IPv6...done
Calling iptables-restore
Calling ip6tables-restore
Configuring network interfaces...waiting for mac s/w reset to be  done
waiting for mac s/w reset to be  done
done.
Initializing random number generator...done.
Starting portmap daemon....
Starting NFS common utilities:.
Cleaning up temporary files....
wdt: WDT device opened.  Watchdog starting with heartbeat = 30 secs
wdt: EMX WDT was enabled at driver open, time remaining 527 secs.
wdt: WDT device IOCTL WDIOC_SETTIMEOUT.  Set heartbeat timeout to 600 secs.
wdt: WDT device closed.  Watchdog will not stop.
wdt: WDT device opened.  Watchdog starting with heartbeat = 600 secs
Starting ILOM Wawdt: EMX WDT was enabled at driver open, time remaining 599 secs.
tchdog daemon.
 Done
wdt: WDT device IOCTL WDIOC_SETTIMEOUT.  Set heartbeat timeout to 30 secs.
populating memstore vars from disk
Running plat...Done running plat
Identifying Product Data...Done
Starting Dynamic FRUID Daemon early init: dynafrud_early_init  Done (0)
INIT: Entering runlevel: 3
Preparsing sensor.xml... ( took 1 seconds ) done
Starting Event Manager: eventmgr  . Done
Starting ipmi log manager daemon: logmgr . Done
Starting portmap daemon...Already running..
Starting NFS common utilities:.
Starting system log daemon....
Starting user mgmt upgrade program: usrmgt_upgrade.
Starting kernel log daemon....
SSH2 RSA key file already exists; Skipping key creation ...
SSH2 DSA key file already exists; Skipping key creation ...
Starting OpenBSD Secure Shell server: sshd.
Starting Health Monitoring Daemon: healthd . Done
Running local boot scripts (/etc/rc.local).
Starting Error Telemetry Collection Daemon: etcd . Done
Starting Fault Diagnosis Daemon: fdd . Done
Starting IPMI Stack: . Done
Starting OpenBSD Secure Shell server: sshd-man.
Starting BBR daemon...
bbrd started after 1 seconds.
Starting Platform Obfuscation Daemon: pod . Done
Starting lu main daemon: lumain . Done
Starting ASR daemon: asr-notify . Done
Starting HT sign on daemon: htsignond . Done
Starting webgo Web Server: webgo . Done
Starting Detection/Diagnosis After System Boot: dasboot  Done
Starting Servicetags discoverer: stdiscoverer.
Starting Servicetags listener: stlistener.
Starting Dynamic FRUID Daemon: dynafrud  Done
Starting FMM Switch Intialization
Enabling switch port 0:ge10 connected to location U6
Enabling switch port 0:ge8 connected to location U5
Enabling switch port 0:ge6 connected to location U4
Enabling switch port 0:ge4 connected to location U3
Starting NMS Events monitoring daemon: ncgf_event_monitord . Done
Retrieving FMM switch firmware version
Starting FMM switch monitoring daemon: ncgf_switch_monitord . Done
Starting NCGF mra fru Daemon: ncgf_configpromd . Done
Starting FMM Hotswap Daemon: ncgf_hswapd . Done
Bringup - Checking for broken symlinks

*** WARNING ***   *** WARNING ***   *** WARNING ***
This is an internal Engineering build with bringup
features enabled and should not be released.


*** WARNING ***   *** WARNING ***   *** WARNING ***
The system appears to be in manufacturing test mode.
Contact Service immediately.


ORACLEFMM-489089M+1515CK0032 login:

This solution has no attachment