Oracle Communications EAGLE (Software)
 

PLA-Support>Sun Systems>CommsGBU>Global Signaling Solutions>SN-SND: Tekelec Eagle 5
 

In this Document

Goal

Solution

Feature Description

Feature Control Requirements

Hardware Requirements

Commands

Limitations

Hardware and Software Considerations

Maintenance Window requirement

Created from <SR 3-9698732561>

Applies to:

Goal

 Enable the Control Feature 72/80 Synchronous E1 High Speed Link (SE-HSLs) (Part Number 893-0130-10/11) on E5 Cards

Solution

Please review the topic "Activating Controlled Features" included on appendix A "Controlled Feature Activation Procedure" of the "Database Administration Manual - System Management" for your correspondent release (e.g. R44.0), it can be downloaded from:

Oracle Communications Documentation for Tekelec products

Database Administration Manual - System Management for EAGLE R44.x

Additional information is below:

Feature Description

The 72 or 80 SE-HSLs on E5 Cards feature allows the SE-HSL feature to support quantities of 72 or 80 high speed links on High Capacity - Multi-Channel Interface Module HC-MIM and E5-E1T1 cards.

Feature Control Requirements

• Feature Access Key (FAK) for Part Number 893-0130-10 — 72 SE-HSL links
• FAK for Part Number 893-0130-11 — 80 SE-HSL links
• After a quantity is provisioned, a lower quantity cannot be provisioned.

Hardware Requirements

Synchronous E1 high-speed links can be added to HC-MIM or E5-E1T1 cards.

Commands

The enable/rtrv-ctrl-feat commands are enhanced to support and display the new quantities.

Limitations

No limitations are associated with this feature.

Hardware and Software Considerations

1. To use an external high-speed master clock source other than RS-422, (Terminal Disk Module) TDMs 870-0774-15 or later must be installed in card locations 1114 and 1116, and the TDM Global Timing Interface options must be configured.
2. verify that the E1 card is an HC-MIM or an E5-E1T1 card:
   • The part number of the HC-MIM is 870-2671-XX.
   • The part number of the E5-E1T1 card is 870-1873-XX.
3. Unchannelized E1 ports cannot be assigned to an E1 card that contains channelized E1 ports. If the E1 ports on the E1 card are channelized, either select another E1 card from the rtrv-e1 output, or add a new HC-MIM or an E5-E1T1 card by performing Adding a LIM-E1 Card.
4. An HC-MIM can contain a maximum of two unchannelized E1 ports. An E5-E1T1 card can contain only one unchannelized E1 port.
5. Serial number is correct and locked.
6. Verify that HIPR cards are installed in card locations 9 and 10 in the shelf containing the HC-MIM or E5-E1T1 card that will contain the E1 port being added.
7. Fans installed and Fan feature ON for HC-MIM card.
8. The HC-MIM can be inserted only in a odd-numbered card location. The HC-MIM will not power up if it is inserted in an even-numbered card location. All the E1 backplane cabling should be removed from the B connector for the slot that the HC-MIM will occupy.
9. The HC-MIM occupies two card locations, so the even numbered card location adjacent to the odd numbered slot where the HC-MIM has been inserted must be empty.
10. The E1, E1/T1 MIM and E5-E1T1 cards occupy one card location. These cards can be placed in any card location except for even numbered card locations whose adjacent odd numbered card location is occupied by a card that occupies two card locations.
11. The HC-MIM and E5-E1T1 card cannot be provisioned as a channel card.
12. If the card is an Embedded Processor Module (EPM) B series based card (E5-E1T1-B), enter the rtrv-stpopts command to verify the Message Flow Control (MFC) option is on.

Please review the appendix A E1 Interface of the "Database Administration Manual - Signaling System #7 (SS7)" for your correspondent release (e.g. R44.0), it can be downloaded from:

Oracle Communications Documentation for Tekelec products

Database Administration Manual - SS7 for EAGLE R44.x

Appendix A E1 Interface

Topics:

• Introduction.....530
• Determining the Configuration.....535
• E1 Interface Configuration Procedures.....538
• Adding a LIM-E1 Card.....539
• Removing a LIM-E1 Card.....544
• Adding Channelized and non-Channel Bridged E1 Ports.....545
• Adding Channel Bridged E1 Ports.....552
• Adding Unchannelized E1 Ports.....558
• Removing the E1 Interface Parameters.....566
• Changing the Attributes of a Channelized E1 Port.....568
• Changing the Attributes of an Unchannelized E1 Port.....573
• Making a Channel Bridged E1 Port from a Channelized E1 Port.....576
• Making a Non-Channel Bridged E1 Port from a Channel Bridged E1 Port.....585
• Adding an E1 Signaling Link.....589

Maintenance Window requirement

As you will add a new feature and add new cards/links/slk or could reconfigure existent cards and move cabling, it is always recommended to do it under a MW despite there is no service impact, see below for additional details:

1. Enabling the feature by itself has no impact on the service.
2. If you will add new cards/links, also there is no impact on the service but new cables will be connected to the frame/shelf, the new cabling can cause service impact: moving an in service link cable during new installation or disconnecting an in service link by mistake.
3. If you need to reconfigure links to free HC-MIM/E1T1 cards, this needs to be done under a MW. Cabling reconnection can cause service impact.

This solution has no attachment