How to Remove and Replace a Netra t 1120/1125 Disk Drive:ATR:1527063.1:1

Asset ID:	1-71-1527063.1
Update Date:	2017-12-13
Keywords:

Solution Type Technical Instruction Sure

Solution 1527063.1 : How to Remove and Replace a Netra t 1120/1125 Disk Drive:ATR:1527063.1:1

Applies to:

Sun Netra T1120 Server - Version Not Applicable to Not Applicable [Release N/A]
Sun Netra T1125 Server - Version Not Applicable to Not Applicable [Release N/A]
Information in this document applies to any platform.

Goal

How to Remove and Replace a Netra t 1120/1125 Disk Drive

*********************************************************************
To report errors or request improvements on this procedure,
please Add a Comment on Doc ID: 1527063.1
*********************************************************************

Fix

DISPATCH INSTRUCTIONS WHAT SKILLS DOES THE FIELD ENGINEER/ADMINISTRATOR NEED?:

Netra t 1120/1125 product training recommended, but not required.

TIME ESTIMATE: 45 mins

TASK COMPLEXITY: 1

FIELD ENGINEER/ADMINISTRATOR INSTRUCTIONS:

PROBLEM OVERVIEW: Disk Failure/Fault

WHAT STATE SHOULD THE SYSTEM BE IN TO BE READY TO PERFORM THE RESOLUTION ACTIVITY?:

The operating system should be configured by the customer such that the disk drive is free for replacement.
e.g. The disk may be part of Solaris Volume Manager, Veritas Volume Manager, mounted file-system, raw partitions, etc.
A data backup may be required to restore data onto a replaced disk.
If a data backup is not required it is still a wise precaution.

WHAT ACTION DOES THE FIELD ENGINEER/ADMINISTRATOR NEED TO TAKE?:

To Remove a Hard Disk Drive

Caution – Use proper ESD grounding techniques when handling components. Wear
an antistatic wrist strap and use an ESD-protected mat. Store ESD-sensitive
components in antistatic bags before placing them on any surface.

1. Attach the wrist strap.

2. Power off the system and remove the input power connector(s).

3. Open the front access cover.

4. Remove the front ESD screen, using a No.1 Phillips-head screwdriver to undo the
two captive screws.

5. Push the handle latch to the right to open the drive handle.

6. Extend the drive handle to disconnect the drive from the system.

7. Holding the drive handle, remove the drive from the drive bay.

8. The hard disk drive rear connector is disconnected when the drive is ejected.

9. Place the drive on an ESD mat.

To Install a Hard Disk Drive

Caution – Use proper ESD grounding techniques when handling components. Wear
an antistatic wrist strap and use an ESD-protected mat. Store ESD-sensitive
components in antistatic bags before placing them on any surface.

1. Attach the wrist strap.

2. Power off the system and remove the input power connector(s).

3. Holding the drive handle, insert the drive into the drive bay.

4. Push the front of the drive to connect it to the SCSI bus.

5. Close the drive handle to lock the drive into the system.

6. Replace the front ESD screen using a No.1 Phillips-head screwdriver.

7. Replace the front access cover.

8. Detach the wrist strap.

OBTAIN CUSTOMER ACCEPTANCE WHAT ACTION DOES THE FIELD ENGINEER/ADMINISTRATOR NEED TO TAKE TO RETURN THE SYSTEM TO AN OPERATIONAL STATE:

Boot system and verify functionality. Reconfigure disk as previously configured. e.g. Part of raid set or mounted file-system or raw partition or other. Restart software applications per applicable administration guides to resume system operation.

PARTS NOTE:

https://support.us.oracle.com/handbook_internal/Systems/Netra_t_1120/Netra_t_1120.html

https://support.oracle.com/handbook_private/Systems/Netra_t_1120/Netra_t_1120.html

https://support.us.oracle.com/handbook_internal/Systems/Netra_t_1125/Netra_t_1125.html

https://support.oracle.com/handbook_private/Systems/Netra_t_1125/Netra_t_1125.html

REFERENCE INFORMATION:

Netra t 1120/1125 Service Manual (805-6804-10): https://support.oracle.com/handbook_private/data/805/805-6804/pdf/

Attachments

This solution has no attachment