Sun Blade T6300 Server Module
 
Sun Blade 6048 System
 
Sun Blade 6000 System
 

PLA-Support>Sun Systems>Sun_Other>Sun Collections>SN-OTH: SPARC-CAP VCAP
 

In this Document

Goal

Solution

References

Applies to:

Goal

How to Remove and Replace the SPARC T6300 Server Module Assembly

********************************************************************************
To report errors or request improvements on this procedure,
please Add a Comment on Doc ID: 1461770.1
********************************************************************************

Solution

DISPATCH INSTRUCTIONS

WHAT SKILLS ARE REQUIRED:
No special skills required, Customer Replaceable Unit (CRU) procedure

TIME ESTIMATE: 60 minutes

TASK COMPLEXITY: 0

REMOVAL/REPLACEMENT INSTRUCTIONS

PROBLEM OVERVIEW: Failed T6300 server module assembly

WHAT STATE SHOULD THE SYSTEM BE IN TO BE READY TO PERFORM THE RESOLUTION ACTIVITY? :

Note: If T6300 is connected to a Disk Module, save the configuration before removing it.
Refer to the Sun Blade 6000 Disk Module Service Manual, http://docs.oracle.com/cd/E19045-01/blade.6000disk/820-1703-13/index.html
and the Sun Blade 6000 Disk Module Administration Guide http://docs.oracle.com/cd/E19045-01/blade.6000disk/820-4922-16/index.html

Note: After replacing the RAID controller (system board), any existing HW RAID volumes (and member disks) may not be seen and need to be re-activated. If the Disk Volumes (including boot volume/disk) become inaccessible, consult: Unable to see a pre-existing RAID volume on Sun Fire[TM] T1000/T2000 Sun Sparc Enterprise T5120/T5140/T5220/T5240/T5440 (Doc ID 1009723.1)

Shut Down the Oracle Solaris OS
Prepare the Server Module for Removal
Remove the Server Module From the Modular System
Remove the Cover
ESD Safety Measures

WHAT ACTIONS ARE REQUIRED:

1.  Prepare to take all ESD precautions when working with both the original server module and the new enclosure assembly.

2.  Prepare to place all components on an antistatic mat unless you install each component immediately in the new enclosure assembly.

3.  Remove the top cover from the original server module and the new enclosure assembly.

4.  Transfer the drives from the original server module to the enclosure assembly.
     Caution - You must return each HDD to the bay from which it was removed.  Use an adhesive note or another method to temporarily label the HDDs after you remove them

5.  Transfer the drive fillers from the original server module to the enclosure assembly.

6.  Transfer the SP card from the original server module to the enclosure assembly.

7.  Transfer the DIMMs from the original server module to the enclosure assembly.
     Move each DIMM to the same slot in the enclosure assembly.

8.  Attach the cover to the enclosure assembly.

9.  Insert the completed enclosure assembly in the same slot as the original server module.

10. Start the server module host.

12. Perform diagnostics to verify the proper operation of the server module.



OBTAIN CUSTOMER ACCEPTANCE

WHAT ACTIONS ARE REQUIRED TO RETURN THE SYSTEM TO AN OPERATIONAL STATE:

Boot system and monitor boot sequence for errors. Test functionality of system:
1. Run the Solaris "fmadm faulty" and SP/ILOM "show faulty" command (if only ALOM is supported run "showfaults -v" command) to verify that the fault has been cleared.
2. Perform one of the following tasks based on your verification results:
   * If the previous steps did not clear the fault, refer to doc 1004229.1 for information about the tools and methods you can use to diagnose and clear
     component faults.
   * If the previous steps indicate that no faults have been detected, the component has been replaced successfully. No further action is required
3. Restart software applications per applicable administration guides to resume system operation.


PARTS NOTE:

https://support.oracle.com/handbook_private/Systems/SunBladeT6300/components.html

REFERENCE INFORMATION:

SPARC T6300 Server Module Service Manual at http://docs.oracle.com/cd/E19076-01/blade.t6300/820-0276-10/index.html

This solution has no attachment