How to Remove and Replace a SPARC T3-1B & Netra SPARC T3-1B Memory DIMMS:ATR:1444725.1:0

Asset ID:	1-71-1444725.1
Update Date:	2017-01-12
Keywords:

Solution Type Technical Instruction Sure

Solution 1444725.1 : How to Remove and Replace a SPARC T3-1B & Netra SPARC T3-1B Memory DIMMS:ATR:1444725.1:0

Applies to:

SPARC T3-1B - Version All Versions to All Versions [Release All Releases]
Sun Blade 6000 System - Version All Versions to All Versions [Release All Releases]
Netra SPARC T3-1B - Version All Versions to All Versions [Release All Releases]
Information in this document applies to any platform.

Goal

How to Remove and Replace a SPARC/NETRA T3-1B Memory DIMMS

*********************************************************************
To report errors or request improvements on this procedure,
please Add a Comment on Doc ID: 1444725.1
*********************************************************************

Solution

DISPATCH INSTRUCTIONS

WHAT SKILLS ARE REQUIRED:
No special skills required, Customer Replaceable Unit (CRU) procedure

TIME ESTIMATE: 30 minutes

TASK COMPLEXITY: 0

REMOVAL/REPLACEMENT INSTRUCTIONS

PROBLEM OVERVIEW: memory DIMM failure

WHAT STATE SHOULD THE SYSTEM BE IN TO BE READY TO PERFORM THE RESOLUTION ACTIVITY? :

DAMAGE ALERT: Perform a visual inspection of the replacement part to make sure that there are no damaged components, connectors, bent pins, damaged packages during shipping, etc. If the part is damaged, don't install it into the system, order a new part. Handle with caution and package carefully the return part to avoid any damages during shipping.

Shut Down the Oracle Solaris OS
Prepare the Server Module for Removal
Remove the Server Module From the Modular System
Remove the Cover
ESD Safety Measures

WHAT ACTIONS ARE REQUIRED:

Remove a DIMM

1. Press the Remind button on the motherboard to identify the DIMMs that need
to be replaced.
2. Push down on the ejector tabs on each side of the DIMM until the DIMM is
released.
3. Grasp the top corners of the faulty DIMM and lift it out of its slot.
4. Place the DIMM on an antistatic mat.
5. Repeat Step 2 through Step 4 for any other DIMMs you intend to remove.
6. If you do not plan to install replacement DIMMs at this time, install filler
panels in the empty slots.

Install a DIMM

1. Unpack the replacement DIMMs and place them on an antistatic mat.
2. Ensure that the ejector tabs on the connector that will receive the DIMM are in
the open position.
3. Push the DIMM into the connector until the ejector tabs lock the DIMM in
place.
If the DIMM does not easily seat into the connector, check the DIMM’s orientation.
4. Repeat Step 2 through Step 4 until all new DIMMs are installed.
5. Install the top cover.

OBTAIN CUSTOMER ACCEPTANCE

WHAT ACTIONS ARE REQUIRED TO RETURN THE SYSTEM TO AN OPERATIONAL STATE:
Boot system and monitor boot sequence for errors. Test functionality of system:
1. Run the Solaris "fmadm faulty" and SP/ILOM "show faulty" command (if only ALOM is supported run "showfaults -v" command) to verify that the fault has been cleared.
2. Perform one of the following tasks based on your verification results:
   * If the previous steps did not clear the fault, refer to doc 1004229.1 for information about the tools and methods you can use to diagnose and clear
     component faults.
   * If the previous steps indicate that no faults have been detected, the component has been replaced successfully. No further action is required
3. Restart software applications per applicable administration guides to resume system operation.

PARTS NOTE:
https://support.oracle.com/handbook_private/Systems/Netra_T3_1B/components.html#Memory

https://support.oracle.com/handbook_private/Systems/Netra_T3_1B/components.html#Memory

REFERENCE INFORMATION:
SPARC T3-1B Server Module Service Manual: http://docs.oracle.com/cd/E19332-01/E29280/E29280.pdf

Netra SPARC T3-1B Server Module Service Manual: http://docs.oracle.com/cd/E20658_01/index.html

Attachments

This solution has no attachment