Sun StorageTek T10000A Tape Drive
 
Sun StorageTek T10000B Tape Drive
 
StorageTek T10000D Tape Drive
 
StorageTek T10000C Tape Drive
 
Sun StorageTek T10000 Tape Drive
 

PLA-Support>Sun Systems>TAPE>Tape Hardware>SN-TP: STK T-Series Drive
 

In this Document

Symptoms

Cause

Solution

Applies to:

Symptoms

 Define Tape Alerts for T10000 Drives

Cause

 Define Tape Alerts for T10000 Drives.

Solution

Tape Alert Flags

0001h Read Warning Drive has difficulty reading.

0002h Write Warning Drive has difficulty writing.

0003h Hard Error Write or read hard error has occurred.

(flags 4, 5, 6).

0004h Media Unrecoverable read, write, or positioning

error caused by faulty media.

0005h Read Failure Hard read error, hardware or media.

0006h Write Failure Hard write error, hardware or media.

0007h Media Life Media has exceeded the life pass count.

0008h Not Data Grade Not supported.

0009h Write Protect Write command was issued to a write-

protected tape.

000Ah No Removal A manual unload or Unload command was

issued while the drive was in prevent removal state – not supported.

000Bh Cleaning Media The tape in the drive is a cleaning cartridge.

000Ch Unsupported Format Unrecognized format.

000Dh Recoverable Snapped Tape Snapped tape – not supported.

000Eh Unrecoverable Snapped Tape Not supported.

000Fh Memory Chip in Cartridge Failure The RFID chip cannot be read or written to.

0010h Forced Eject A manual eject was performed before a reposition to BOT was commanded.

Not supported.

0011h Read Only Format Not supported.

0012h Tape Directory Corrupted MIR corrupted.

0013h Nearing Media Life The tape is nearing the end of its

calculated life.

0014h Clean Now The drive has determined it needs cleaning.

0015h Clean Periodic Cleaning counter has reached threshold,

cleaning LED is on.

0016h Expired Cleaning Media The last cleaning cartridge inserted was used

up – not supported.

0017h Invalid Cleaning Media Not supported.

0018h Retention Requested Not supported.

0019h Dual port interface error Not supported.

001Ah Cooling fan failure Not supported.

001Bh Power supply failure Not supported.

001Ch Power consumption Not supported.

001Dh Drive Maintenance Preventive maintenance of the drive is

required.

001Eh Hardware A Drive has a hardware fault .

001Fh Hardware B Hardware not read/write related – not

supported.

0020h Interface Having problems with the interface, SCSI

parity errors detected.

0021h Eject Media Eject the media and retry, load failure not

tape snap.

0022h Download Fail Microcode update failed.

0023h Drive Humidity Not supported.

0024h Drive Temperature  Temperature inside the tape drive is above

specified range.

0025h Drive Voltage Not supported.

0026h Predictive Failure A hardware failure of the drive is predicted.

0027h Diagnostics Required Dump available.

0028h thru 002Eh Reserved for CSL

002Fh thru 0031h Reserved

0032h Lost Statistics Media statistics lost some time in the past.

0033h Tape Directory Invalid at Unload The tape directory on the tape cartridge just

unloaded has been corrupted.

0034h Tape System Area Write Fail The tape just unloaded could not write its

system area successfully.

0035h Tape System Area Read Fail The tape system area could not be read

successfully at load time.

0036h No Start of Data The start of data could not be found on tape.

0037h Loading failure The operation has failed because the media

could not be loaded and threaded.

0038h Unrecoverable Unload failure The operation has failed because the media

could not be unloaded.

0039h Automation Interface failure Not supported.

003Ah Firmware failure - The tape drive has reset itself due to a detected firmware fault. This will occur when a SNO occurs as a secondary result. Check the drive for a SNO dump.

This solution has no attachment